Abstract
This study examined the effect of alkalis on lyocell-based activated carbon fibres (ACFs) with high Brunauer-Emmett-Teller (BET) surface areas, using X-ray diffraction (XRD). Here, alkali treatments were conducted using 10 ~ 25 % NaOH and KOH on lyocell samples for 3 h at ambient room temperature. A secondary treatment with..... More

Abstract
Cu-Ni-Si alloys were strengthened by Ni₂Si intermetallic compound precipitation in a Cu matrix during aging. The Cu-6 wt% Ni-1.4wt%Si alloy was prepared by water quenching (solution treatment) or air cooling (homogenization treatment) after heating 980 ^oC for 2 hours and aging at 500 ^oC for 6 hours. After maintaining a..... More

Abstract
The subject of this study was a bronze sword excavated from the early Iron Age area of Sinpung site in Wanju. SEM-EDS, FE-EPMA and Raman Micro-Spectroscopy analysis methods were applied to investigate the manufacturing techniques and corrosion characteristics. The results of the analysis indicated a casting structure composed of both..... More

Abstract
We report on the phase transition behavior and thermoelectric transport properties of Zn-doped Cu₂Se. Cu₂Se is comprised of nontoxic, low-cost and abundant elements, and has been attracting attention because of its very high thermoelectric performance, ZT, at high temperatures. Many studies have reported enhanced ZT in impurity doped Cu₂Se, however,..... More

Abstract
A stripping solution with thiourea, iron(III) sulfate, and sodium dodecyl sulfate(SDS) was employed to strip Ni-based 14 karat white gold alloys, and the formation of the NiS byproduct and elimination of passivation were investigated in the presence of 0.0-0.2 g/L SDS. White gold alloy samples with a flat shape were..... More

Abstract
Technologies for pedestrian safety are increasingly emphasized by Automakers in advance of autonomous driving vehicles. A Night Vision System attached behind the front grille can reduce fatal accidents, especially during the nighttime, however, consumers may hesitate to adopt such systems on account of their high price. High-cost Germanium is used..... More

Abstract
Ionic liquids have emerged in hydrometallurgy as potential extractants for metals. In this work, the interactions of ALiCY (R₄N⁺A^-) synthesized by Aliquat336 and Cyanex272, and a mixture of ALiCY and TBP, were analyzed using extraction data and FT-IR spectroscopy. Co(II) and Ni(II) were extracted from two HCl concentrations (1.0×10^-4 and..... More

Abstract
In this study, solidification cracking behavior and susceptibility in dissimilar cladding of Inconel alloy FM 52, 308L stainless steel to carbon steel, was investigated by submerged arc welding and transverse−Varestraint testing with gas tungsten arc welding. The effect of cladding conditions on cracking behavior and susceptibility was extensively evaluated, and..... More

Abstract
Pores and cracks are known as the main defects in metal additive manufacturing (MAM), including directed energy deposition(DED). A gaseous fume is often produced by laser flash (instantaneous high temperature) during laser processing, which may cause various defects such as porosity, lack of fusion, inhomogeneity, low flowability and composition change,..... More

Abstract
New technologies need to be developed in the ironmaking process to reduce carbon dioxide emissions. To achieve this, in recent years steelmakers have been working to reduce coke usage by increasing thermal energy efficiency. However, it is very difficult to reduce coke consumption while maintaining production, because the level of..... More

Abstract
Polyurethane foam (PUF) is one of the most well-known cellular materials and is widely employed in various industrial and biomedical fields thanks to its many advantages. These include mechanical and material characteristics such as low density and thermal conductivity, and high specific elastic modulus and strength. Despite of these advantages,..... More

Abstract
TiO₂ nanostructures were synthesized using a thermal evaporation method without a catalyst. TiO powders mixed with graphite powders were used as the source materials. The synthesis process was performed in air atmosphere at 1000 °C. When the mass ratio of TiO/graphite in the source material was 2:1, TiO₂ nanowires and..... More

Abstract
We report the thermoelectric transport properties of n-type Bi₂Te_2.7Se_0.3 compounds prepared by oxide-reduction process. The oxide-reduction process is a recently developed method that can synthesize Bi2Te3-based compounds using only oxide starting materials, which is advantageous in terms of the diversity of the starting materials and cost efficiency. In this study,..... More

Abstract
This study investigated the removal of the organic dye like methylene blue using porous particles in a batch adsorption process. Porous silica microparticles were synthesized with macropores or meso-macropores and used as adsorbent particles. The hierarchically porous structures with additional mesopores were found to be more effective adsorbent than simple..... More

Abstract
In this study the correlation between bainitic microstructure and the low-temperature toughness of high-strength API pipeline steels was discussed in terms of crack initiation and propagation in the microstructure. Three types of API pipeline steels with different bainitic microstructures were fabricated using varying alloying elements and thermo-mechanical processing conditions, and..... More

Abstract
In this work, LiOH was synthesized using highly soluble Li₂SO₄. To enhance efficiency, this synthesis was performed using the precipitation method, and the correlation between each experimental condition and the synthesis of LiOH was investigated. The particle size and crystalline properties were tailored by controlling various experimental conditions, including the..... More

Abstract
In this study, Fe₂O₃ photoelectrode thin films were grown on fluorine-doped tin oxide substrates at various temperatures ranging from 145 to 220 oC using modified chemical bath deposition. The morphological, structural, electrical, and photoelectrochemical properties of the resulting Fe₂O₃ photoelectrode were analyzed using field emission scanning electron microscopy, X-ray diffraction,..... More

Abstract
Three kinds of Ni-based single crystals with the compositions of 63.8Ni-7.5Cr-5.1Co-4.8Al-1.9Mo- 0.9Ti-3Re-11.8Ta-1.2W, 61.4Ni-7.4Cr-5Co-4.8Al-1.8Mo-0.9Ti-3.1Re-11.6Ta-4W, and 60.9Ni-7.5Cr-5Co-4.8Al- 2Mo-1Ti-2.9Re-10.9Ta-1.2W-3.8Ru, in wt%, were cast in a Bridgman furnace. In the cast alloys, Cr, Co, Re, Mo, W, and Ru became microsegregated in dendrites consisting of γ-Ni, while Ni, Ta, and Al microsegregated in interdendrites..... More

Abstract
In this study, the effects of nickel and copper on the mechanical and thermal properties of Al-Si alloys were investigated, for different alloy compositions. Thermodynamic calculations were carried out to predict the alloys’ solidification behavior (solidification temperature, solid fraction and physical properties (density, thermal conductivity, elastic modulus, bulk modulus)). The..... More

Abstract
Materials with very small dimensions exhibit different physical and mechanical properties compared to their bulk counterparts. This becomes significantly important for the thin films that are widely used as components in micro-electronics and functional materials. In this study, a chromium (Cr) thin film was deposited on a silicon (Si) wafer..... More

Abstract
Quarternay carbides of Ti₃Al_xSi_1-xC₂ (x=0.3, 0.5, and 0.7) were oxidized at 400, 600, and 800 °C for 0.5-6 months in order to study their long-time oxidation behavior in air. When they were oxidized at 400-600 ^oC for 0.5-3 months, oxidation proceeded relatively slowly with moderate weight gains. However, further oxidation..... More

Abstract
A superelastic titanium alloy was subjected to uniaxial tensile deformation at room temperature. The microstructural evolution and deformation mechanisms of the superelastic titanium alloy were investigated by electron backscatter diffraction (EBSD) and X-ray diffraction (XRD). Multiple deformation mechanisms including stress-induced martensitic transformation (SIMT), dislocation slip, {332}<113> and {112}<111> mechanical twinning..... More

Abstract
The nanofabrication of modern electronic devices requires advanced nanopatterning technologies. To fabricate desirable nanodevices with excellent device performance, controlling the shape and dimension of the pattern is very important. However, to achieve more facile and faster device fabrication, with better pattern resolution, pattern-tunability, process simplicity, and cost-effectiveness, some remaining challenges..... More

Abstract
Radio frequency identification (RF-ID) uses electromagnetic fields to automatically identify and track tags attached to objects. In response to the need to suppress the electromagnetic interference between adjacent RF-ID equipment or systems, this study aims to achieve a thin and multi-resonance absorber using metamaterials composed of patterned grids on a..... More

Abstract
As global regulations of CO₂ emissions and fuel consumption efficiency become more strict, the automotive powertrain system has become more compact with lower lubrication viscosity. With the current trends in powertrain system improvement, the operating conditions of powertrain components such as gears are becoming more severe. As a result, it..... More

Abstract
In this study, an electrospray technique was used for the synthesis of macroporous ceramic particles, such as silica or titania, by a colloidal templating method. For this purpose, a suspension of polystyrene nanospheres was synthesized by dispersion polymerization for use as sacrificial templates. The feed solution containing a ceramic precursor..... More

Abstract
This study created alumina structures with the highest hydrophilic properties on 6061 aluminum alloy. The anodization process was applied to make various aluminum oxide structures. To create uniform alumina structures on top of a 6061 aluminum alloy surface, after conducting the first anodization in 0.3 M oxalic acid at 40..... More

Abstract
The growth of the PEO coating with processing time on an AZ31B magnesium alloy in a dilute alkaline electrolyte containing silicate and the corrosion characteristics according to its thickness were investigated. The oxide film grew a porous outer layer mainly consisting of silicate with the spark discharge phenomenon from the..... More

Abstract
Liquid immiscible alloy systems present a unique opportunity for designing composites with sphere-dispersed and/or interconnected microstructures. Herein, we demonstrate that the addition of Pb in Al₈₄TM₁₀RE₆ (TM=Ni,Co,Fe,Ti, RE=La,Ce,Nd,Gd,Y) metallic glasses can result in liquid-liquid phase separation in a liquid immiscibility gap and substantially solidifies into a Pb-rich crystalline phase and..... More

Abstract
In this study, we investigated the morphological, crystal structural, electronic structural, and electrocatalytic properties of the inverse spinel structured copper cobalt oxide (Cu_0.72Co_2.28O₄) catalysts. The materials were prepared by coprecipitation using various copper and cobalt precursors, and subsequent oxidation treatment. Electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and Brunauer Emmett..... More